brodcade Huawei and NFA
Hi I want to ask you if i can monitor the Switch Brodcade Huawei by NFA and the same thing concerning Enterasys N7 if yes can you send me a steps to configuration RegardsAhmed
View ArticleRe : brodcade Huawei and NFA
Hi Ahmed,Thank you for visiting our forum website.Please check the links below and let us know if you need further...
View ArticleClik here to view.
Importing Existing Flow-tools Data to Netflow analyzer
hi, I have got some history Netflow data from flow-tools as in figure below, Can I import these data to Netflow analyzer? Thanks.
View ArticleRe : Importing Existing Flow-tools Data to Netflow analyzer
Hi ,Thank you for visiting our forum website. Currently it is not possible to import data from any tools. Thanks & Regards,Senthil.N
View Articlejuniper srx3400 Interface flow problem
These days, in the use of NAF 9.8.6. We found that the juniper equipment and the flow of the actual flow gap, only the actual flow rate of 1/10, or even less. Do not know what method can solve this...
View ArticleRe : juniper srx3400 Interface flow problem
Hi,Thank you for writing to us. Please find the commands below to configure Jflow in juniper device.forwarding-options {sampling {input {family inet {rate 1000;run-length 9;max-packets-per-second...
View ArticleClik here to view.
Re : juniper srx3400 Interface flow problem
Thank you for your reply This is the interface configuration information reth1 { redundant-ether-options { redundancy-group 1; } unit 0 { family inet {...
View ArticleClik here to view.
Re : juniper srx3400 Interface flow problem
This is now the NetFlow sampling results. OMG
View ArticleRe : juniper srx3400 Interface flow problem
Hi ,Thank you for your post. If you have set rate 1000 in the device, set the sampling rate as 100 in NetFlow UI. If the issue persist, please send us your contact detail to...
View ArticleUnable to Capture Outbound Traffic
Hi, I'm using Cisco 7606s and GSR 12406 as my border. I'm unable to capture outbound traffic from the interface. Below is the config from my router. I have done a lil bit of research on how to over...
View ArticleRe : Unable to Capture Outbound Traffic
Hi Kanna, Thank you for writing to us. Please make sure that you have configured the 7600 series device as mentioned in the below link:...
View ArticleRe : Customize WEB Interface
Hi,Yes, you can monitor the Mikrotik Router using NetFlow Analyzer. Please configure the Mikrotik router as mentioned in the below link...
View ArticleCustomize Dashboard Question
I have several different companies that I am monitoring. I'd like to have a dashboard that shows the bandwidth utilization for each of those companies on one page. Is that possible?
View ArticleRe : Customize Dashboard Question
Hi ,Thank you writing to us. NetFlow Analyzer does not have the requested features available. The dashboard will show the statistic of all the devices that are sending flows to the NetFlow Analyzer...
View ArticleRe : Device Listing in UI
HI,Could you please let us know the product you are referring to so we can assist you accordingly.Regards,Arun Karthik Asokan
View ArticleHow to register Netflow Analiser Plugin Opmanager
Hi ! Please, I'd like register my netflow analiser plugin installed on opmanager.I have file the license "AdventNetLicense" XML Document, but I don't know how to install, or I don't know what directory...
View ArticleRe : How to register Netflow Analiser Plugin Opmanager
Hi,You can apply the license received by clicking on Support -->Register at the top- right corner of the OpManager user interface. In case not able to apply the license file due to some error,...
View ArticleRe : Ifindex Naming
I can use the troubleshoointg snmpwalk.sh which tells me SNMP is working. However the web gui still uses Index even after I try to change it to use ifName. The Web gui is not pulling the interface...
View ArticleСan not see the traffic that generates the router itself
Hello.I have cisco 3921. Internet connected to Gi0/1 interface. Lan connected to Gi0/0 interface.On both interface i use 'ip route-cache flow' command.Traffic comes from Gi0/0 interface. Then traffic...
View Article
